Molybdenum Disulfide For Plastics is added to plastics to make modified plastics containing molybdenum disulfide powder, which can improve its bearing capacity and wear resistance without affecting the impact resistance and fatigue resistance of unmodified plastics such as cast nylon , widely used to manufacture gears, bearings, star wheels and sleeves, can widely replace wear-resistant parts of mechanical equipment, replace copper and alloys as wear-resistant and wearing parts of equipment, such as bushings, bearing bushes, bushings, lining plates, Gears, worm rollers, copper guide rails, piston rings, sealing rings, sliders, ball bowls, impellers, vanes, cams, nuts, valve plates, pipes, stuffing boxes, racks, pulleys, pump rotors, etc.
Molybdenum Disulfide For Plastics is a good solid lubricant that can be lubricated in a vacuum or air environment for a long time. The friction coefficient is relatively low, and Molybdenum Disulfide For Plastics can be lubricated for a long time in the air below 350 ℃.
With more than ten years of R&D experience, we can provide an annual output of 1,000 tons of Molybdenum Disulfide For Plastics as a patented technology product.
Molybdenum Disulfide For Plastics is a lubricant grade of molybdenum disulfide (MoS2) available in three grades-Technical, Technical Fechnical Fine,and Super Fine.Typical MoS2 content (calculated average) is 98.5%.
Molybdenum Disulfide For Plastics
Introduction
Molybdenum Disulfide For Plastics is added to plastics to make modified plastics containing molybdenum disulfide powder, which can improve its bearing capacity and wear resistance without affecting the impact resistance and fatigue resistance of unmodified plastics such as cast nylon , widely used to manufacture gears, bearings, star wheels and sleeves, can widely replace wear-resistant parts of mechanical equipment, replace copper and alloys as wear-resistant and wearing parts of equipment, such as bushings, bearing bushes, bushings, lining plates, Gears, worm rollers, copper guide rails, piston rings, sealing rings, sliders, ball bowls, impellers, vanes, cams, nuts, valve plates, pipes, stuffing boxes, racks, pulleys, pump rotors, etc.
Molybdenum Disulfide For Plastics is a good solid lubricant that can be lubricated in a vacuum or air environment for a long time. The friction coefficient is relatively low, and Molybdenum Disulfide For Plastics can be lubricated for a long time in the air below 350 ℃.
With more than ten years of R&D experience, we can provide an annual output of 1,000 tons of Molybdenum Disulfide For Plastics as a patented technology product.
Molybdenum Disulfide For Plastics is a lubricant grade of molybdenum disulfide (MoS2) available in three grades-Technical, Technical Fechnical Fine,and Super Fine.Typical MoS2 content (calculated average) is 98.5%.
Chemical Specifications of Molybdenum Disulfide For Plastics：
Maximum % by wt | Maximum % by wt | Maximum % by wt | |
Technical | Technical Fine | Super Fine | |
Acid Insoluble | 0.50 | 0.50 | 0.50 |
Iron | 0.25 | 0.25 | 0.25 |
Molybdenum Trioxide | 0.10 | 0.10 | 0.15 |
Water | 0.20 | 0.20 | 0.20 |
Oil | 0.05 | 0.40 | 0.40 |
Carbon | 0.50 | 0.50 | 0.50 |
Acid Number | 0.05 | 0.50 | 3.0 |
*Acid number is determined at time of production. Prolonged storage will result in slight oxidation,which will produce an increase in acid number.The smaller particle size grades are more susceptible to surface oxidation.Acid number is expressed as an absolute value and is the mg of KOH required to neutralize the acid in a one-gram sample.
Particle Size Specifications of Molybdenum Disulfide For Plastics By Microtrac：
Grade | D50 | D99(Maximum) |
Technical | 16.0-30.0μm | 180μm |
Technical Fine | 4.0-6.0μm | 35.0μm |
Super Fine | 0.9-1.5μm | 6.5μm |
Typical Particle Size of Molybdenum Disulfide For Plastics By Microtrac By Fisher Sub-sizer and Bulk Density:
Grade | Fisher Number, μm | Bulk Density(Scott) |
Technical | 3 to 4 | 1.3g/cm3 |
Technical Fine | 0.65 to 0.80 | 0.4g/cm3 |
Super Fine | 0.40 to 0.45 | 0.3g/cm3 |
Packaging of Molybdenum Disulfide For Plastics ：
Grade | US Packaging Fiber Drum | Pallet weight |
Technical | 25kg | 450kg |
Technical Fine | 25kg | 450kg |
Super Fine | 25kg | 450kg |
18 drums/pallet | ||
FIG.1 PTFE sealing ring with added Molybdenum Disulfide For Plastics
FIG.2 Modified nylon products with added Molybdenum Disulfide For Plastics.
FIG.3 Molybdenum Disulfide For Plastics packing 25kg fiber drum.
On January 30, 2023, molybdenum price rose by more than 20% in a single day, breaking a new 17-year high. Molybdenum is known as the "war metal", "steel warrior". Molybdenum is valued by more and more countries. China is the world's richest country in molybdenum resources, with reserves of 4.3 million tons, followed by the United States (2.7 million tons) and Chile (1.8 million tons), which acco...more
